Wavlink Wifi Extender Setup | AP.Setup | wifi.wavlink.com

Wavlink Wifi Extender Setup using AP.Setup

Simplest and easy guide

Wavlink Wifi Extender
Setup using AP.Setup

Simplest and easy guide

wifi.wavlink.com setup Via Ap.setup

  1. The device you wish to setup (the one with the “wifi.wavlink.com” interface) should be connected to your computer or mobile device.
  2. IP addresses 192.168.0.1 and ap.setup are typical defaults.
  3. Usually, a label on the gadget or the handbook will include this information.
  4. Once you’ve logged in, search for the “Wireless Settings” or “Network Settings” option.
  1. There should be a “Access Point” or “AP Mode” option in this section.
  2. Input a passphrase or network key, the desired network name (SSID), and security parameters (such as WPA2-PSK).
  3. Once the parameters have been adjusted, save the modifications.
  4. You may receive a prompt from the device to restart or apply the settings.

Note:- Facing issues during the wifi.wavlink.com setup via ap.setup, reach out to our experts for assistance.

wavlink wifi extender setup

Why is it important to configure the Wavlink WiFi Extender?

 

The main purpose of the Wavlink wifi range extender setup device is to extend the network range of your Wi-Fi device. If you really want to enjoy high-quality 4K videos on your smartphone, laptop, computer, or on LED TV, then the Wavlink Wi-Fi extender setup is required for a strong, reliable, high-speed, and fastest network.

Steps To Access The WiFi Wavlink Login Page.

  • First, you must use an Ethernet cable to connect your extender to the router and any Wi-Fi-enabled devices.
  • After connecting the device, open any browser to proceed further such as Microsoft Internet Explorer, Mozilla Firefox, or Apple Safari.

 

Search wifi.wavlink.com or http://192.168.10.1, choose your language and then enter the username and password of the admin. Click on login button to finalize the Wavlink login Process.

WiFi-Wavlinkext- login-steps

“Complete the Wavlink login setup process by adding default username and password. You can add new password if changed during setup previously

wifi.wavlink.com setup Via Manual method

This procedure is made up of several steps and prerequisites. While using manual method use of WPS setting won’t be required.

Before you can use your extender, you must first configure it. To ensure that the entire process runs smoothly, follow the steps in the order listed below, without skipping any step:

  • To begin, connect your wall outlet to the Wavlink WiFi Extender and turn it on.
  • Bring both the devices your extender and router closer till Wavlink extender setup is not complete.
  • Connect your Wi-Fi device to the Wavlink EXT network at this point.
  • After that, launch any browser and type http://wifi.wavlink.com into the address bar.
  • You will get Wavlink extender setup page on doing these steps.
  • Follow the instructions provided on the screen.

wifi.wavlink.com setup Via Wps

Before you begin, make sure your wireless router is WPS-compatible.

The WPS button makes it easier to extend your host network. With the help of the WPS procedure, it will take a few minutes to configure the Wavlink wifi range extender setup and it won’t take much time at all.

This setup process won’t require user ID and password of your Wavlink extender. Follow the below mentioned guidelines for the Wavlink Wi-Fi range extender setup using the WPS method.

  • Move your Wavlink Wi-Fi range extender closer to your main router or modem to start the process.
  • Establish connection between power extender and power outlet.
  • Continue to watch until the power light turns on.
  • At this point, press the WPS button for 2-3 seconds on your Wavlink Wi-Fi extender. Then, let go of the WPS button.
  • After that, press the WPS button on the Wi-Fi router and wait for thirty to forty seconds for the two devices to sync.
  • If you get the green LED light on your extender signal that means your Wavlink extender has been successfully connected with your Wi-Fi network.
  • To finish the setup process open ap.setupWavlink.
  • Once the configuration is complete, place the Wi-Fi booster where you want it.
WPS Process (Wavlink Extender Installation with WPS button)

Ap Setup Login

  • Make that the connection has been made.
  • You must ascertain the access point’s IP address.
  • Usually, the gadget’s handbook or a label on the device itself have this information.
  • IP numbers 192.168.0.1 and 192.168.1.1 are often used.
  • On the device you’re linked to, launch a browser.
  • To find out the default login information, consult the device’s label or handbook.
  • “Admin” is a common default for both the username and password.
  • However, it’s advised to alter these settings for security-related concerns.

  • Once you’ve logged in, search for the “Wireless Settings” or “Network Settings” option.
  • There should be a “Access Point” or “AP Mode” option in this section.
  • Input a passphrase or network key, the desired network name (SSID), and security parameters (such as WPA2-PSK).
  • Once the parameters have been adjusted, save the modifications.
  • You may receive a prompt from the device to restart or apply the settings.

Facing Common issue during wifi.wavlink.com setup

  • wavlink wifi extender setup error
  • Can’ connect to wifi
  • ap.setup login issue
  • Can’t access the web page of wavlink
  • Issue with power source
  • Connection issue with devices
  • Outdated firmware
  • Wavlink app access error
  • Cache issue
  • Browser issue
  • Firewall or antivirus
  • Device needed reboot
  • Wifi.wavlink.com login error
  • wavlink extender not connecting to internet
  • Can’t I connect to 192.168.10.1

wavlink extender troubleshooting 

  • Make sure your router or access point has a steady power supply and that all of the cords are firmly attached.
  • Authenticate that the browser is displaying the correct web address, wifi.wavlink.com.
  • To get the correct setup address, try looking through the user manual or paperwork that came with your device, if at all possible.
  • Try using the device’s IP address to visit the setup interface instead of the domain name.
  • This usually looks like 192.168.0.1 or 192.168.1.1.
  • Check the handbook of your gadget to find the correct IP address.
  • Perhaps outdated data is being stored by your browser.
  • Before attempting to use the setup interface once more, make sure your web browser is clear of cookies and cache.
  • To rule out any browser-specific problems, try utilising a different web browser to access the setup interface.
  • See if your router or access point has any firmware upgrades available.
  • Device performance can be enhanced and known issues can be fixed by updating the firmware.
  • Turning off your router, waiting a minute, and then turning it back on is known as a power cycle.
  • Remember that doing this will remove any customised settings, so be sure you go to the handbook for your device to find out the correct procedure for resetting it.
  • Switch off these security mechanisms for the time being and try to access wifi.wavlink.com once more.
  • Depending on the brand of your device, they might offer particular advice or solutions for the wifi.wavlink.com setup.

How to reset wavlink extender

There are two common ways to reset a Wavlink extender: a hard reset and a gentle reset. Each kind of reset can be carried out as follows:

Hard Reset (Factory Reset):

Erasing all customised configurations, a hard reset returns your Wavlink extender to factory default settings. Take these actions:

  • Look for your Wavlink extender’s reset button.
  • Push and clasp the reset knob
  • Hold it in place until the extender’s LED lights react, which could involve blinking or changing patterns.
  • Let go the reset knob
  • Usually, the LED lights will show after the procedure is complete.
Hard Reset
Soft Reset

Soft Reset:

Frequently used to restart the extender without erasing your customised settings, a soft reset is less extreme than a factory reset. Take these actions:

  • Open a web browser and connect to the Wavlink extender there.
  • IP numbers 192.168.0.1 and 192.168.1.1 are often used.
  • Enter the login information for your extender.
  • The default username and password are frequently “admin” or are listed in the extender’s manual if you haven’t changed them.
  • Search for a reset or reboot option for the extender.
  • To validate the reboot, adhere to the on-screen directions.
  • Your settings won’t be lost when the extender restarts.

wavlink extender not connecting to internet

  • Make sure the Wavlink extender is positioned appropriately.
  • Signal Strength: Check the LED indications on the extension to make sure there’s a strong Wi-Fi signal coming from the router.
  • Verify sure the extender is linked to the appropriate wireless network by checking the connection.
  • Turn on and off the router, extension, and any attached electronics.
  • Verify that the correct SSID and password are configured on the extender.
  • Substantiate whether the Wavlink extender has any available firmware updates, then install them.
  • Take into account doing a factory reset and putting the extender up correctly this time.
  • If problems continue, get in touch with Wavlink support for more help.

Wavlink Wifi Extender Setup

how do i connect my wavlink to wifi

  • Place the Wavlink extension into your router’s effective range.
  • Use a browser to access the web interface after connecting a device to the Wavlink’s default network
  • Enter the default login information for the extender, which is often “admin” for both the username and password.
  • Save the configurations and use them.
  • Join the enlarged Wi-Fi network with your devices.
  • Examine the LED indications on the device to make sure the connection is steady.

Can’t I connect to 192.168.10.1

  • Verify that the device you are using is linked to the same network as the one that has the IP address 192.168.10.1.
  • Make sure the IP address 192.168.10.1 is the right one for your device.
  • Consult the device’s handbook or look over the labels.
  • temporarily inactivate antivirus and firewall since they might be preventing access.
  • To rule out wireless problems use ethernet.
  • If problems continue, think about doing a factory reset or contacting support for help.

FAQs

Most frequent questions and answers

If you are looking to setup your WiFi wavlink extender using Ap.setup, 192.168.10.1, you can start with http://ap.setup/ in the address bar. If this URL does not work, enter the default IP address, 192.168.10.1, into the address bar.

Use below given steps for your extender setup using ap.setup method:

  • We will start with connecting our range extender to power and check for the light to show green.
  • After waiting for 2 minutes we will press WPS button on both router and extender devices.
  • Another method for configuring your Extender is to connect it to the router using an Ethernet cable
    andthen use a computer to access the website http://ap.setup/, which is an offline configuration page for the extender.
  • Plug in the extender to the outlet and wait for 45 seconds for startup.
  • Once the LED Light starts flashing red on the extender then press and holds the WPS button on your router for approx. 5 seconds.
  • When you notice that the WiFi signal is changing colour and starts blinking then you can release the WPS button on the router.
  • Press the WPS button on the extender approx 6 seconds until you see blinking blue light. Now it’s started to communicate with the router.
  • Connection process takes 60 seconds. You will know that the extender is connected to the router once the blinking lights turn into solid blue.
  • That’s how you can connect your extender with the router.
  • Connect to Wavlink WiFi Extender using a cellphone.
  • Plug the extender into an outlet and wait for 45 seconds for the LED light to be blinking red.
  • Go to the WiFi settings and search for Wavelink-N or Wavlink-AC then tap on it.
  • Open a web browser on your phone and enter 192.168.10.1 into the web address bar.
  • Enter the default login detail that’s default username and password.
  • Next time you can also change the password if you want.
  • That’s how you can connect with the Wavlink WiFi extender using your cellphone.
  • Enter 192.168.10.1 in the address bar of the browser.
  • You can see Wavlink extender login on your screen.
  • Enter the default login details.
  • Press the login button.
  • Username and password should be case-sensitive.
  • Move on to the WiFi option and then you need to press the Wireless settings tab.
  • Enter the desired SSID name and Wi-Fi password which you want to be changed.
  • After changing the password and other WiFi settings, press the Apply button.
  • Settings can take some time to finish the process on the router.
  • That’s how you can change the WiFi password of the router.